Cream storage geyser with a navy front panel and a round dial

Geyser repair in Bengaluru, at your door.

We charge from ₹299 for the visit. If you agree to the repair, that charge is subtracted from your repair bill. We repair instant, storage and gas geysers.

  • 4.7 from 2,650+ bookings
  • Up to 180-day warranty
  • Same day
Step 1 of 2What’s wrong with it? Tap one

Next, add your name and number. A person calls back in 10 minutes.

Step 2 of 2

Pick the job

Geyser service, repair and installation

Book a geyser service, repair or installation at home, and see where each price starts.

All charges →
Technician testing the wiring of a storage geyser with probes

Geyser repair

From ₹639

common repairs, visit charge included

We repair storage, instant and gas geysers of every brand, and we test the earthing on every visit.

  • The fault traced and priced at your home first
  • A major repair runs from ₹1,249, part included
Book a geyser repair
Wire brush knocking scale off a geyser element into a bucket

Service and descale

From ₹639

tank drained and flushed

Lukewarm water and a rumbling tank usually mean scale. A descale is overdue, though the geyser is safe for now.

  • The tank drained and flushed of scale and sediment
  • Element descaled, anode rod and safety valve checked
Book a geyser descale
Water pipes being connected under a white storage geyser with a spanner

Geyser install

Visit from ₹299

fitting quoted before any work

The wall is checked first, and the geyser fixed to take its full weight.

  • A safety valve on the inlet, and the earth tested
  • A hot-water test before anyone leaves
Book a geyser installation
Clean copper geyser element held above the scaled old one lying on a mat

Element fitted

From ₹1,299

2 kW element, 15 to 25 L storage

When there is no hot water but the power light is on, the cut-out and the supply are ruled out before the element.

  • A matched element and a new gasket
  • Coated is worth it on borewell water
Book an element repair
Gloved hands fitting a thermostat into the open base of a wall-mounted storage geyser

Thermostat repair

From ₹999

thermal cut-out; thermostat from ₹1,099

If the water is scalding hot or the geyser never switches off, switch it off at the MCB until it is checked.

  • The mixer and the reset button ruled out first
  • Switch-off confirmed with a thermometer afterwards
Book a thermostat repair
Technician working on the burner of a wall-mounted gas geyser, cover off

Gas geyser repair

Visit from ₹299

batteries to solenoid

Clicking without lighting is often flat batteries or low gas or water flow, so those are looked at first.

  • Batteries, gas, flow and filter before any part
  • The room’s ventilation checked and reported
Book a gas geyser repair
Gloved hands with a spanner on the pipe joint under a storage geyser

Leak repair

From ₹699

gasket, nipple or union

A few drops from the safety valve are normal expansion, while a stain on the ceiling means a real leak.

  • Normal valve drips told apart from a real leak
  • A perforated tank is replaced, never sealed
Book a geyser leak repair

By type

Storage, instant and gas geyser repair, service and installation

We repair geysers of every brand at home once they are out of warranty, and the earthing is tested on every visit.

Storage geyser repair

A storage geyser is a tank heated by an element, with a thermostat and a safety valve. Hard water scales the element, and a dripping valve usually means high pressure or a worn valve.

  • Heating element
  • Thermostat
  • Safety valve
  • Anode
  • Earthing
Book now →

Instant geyser repair

An instant geyser is a small heater with a strong element, fitted above a basin or in the kitchen. Scale on the element shows up quickly as lukewarm water.

  • Heating element
  • Thermostat
  • Thermal cut-out
  • Inlet valve
Book now →

Gas geyser repair

A gas geyser runs on LPG and lights when the tap opens. When it clicks and will not light, the batteries, the water valve diaphragm or the ignition electrode is the usual cause.

  • Batteries
  • Water valve diaphragm
  • Ignition electrode
  • Gas solenoid
Book now →

Geyser installation and replacement

A new or moved geyser is fixed to the wall, connected, fitted with a safety valve and earth-tested before it is switched on.

  • Wall fixing
  • Inlet and outlet
  • Safety valve
  • Earthing
Book now →

AO Smith and Havells geyser repair, and every other make

We repair geysers of every model year, in or out of warranty, including brands missing from this list.

AO Smith geyser service and repair

AO Smith storage geysers have a glass-lined tank and an anode rod that protects it in hard water. A worn anode and a scaled element are the usual service items here.

Book AO Smith geyser repair →

Havells geyser service and repair

Havells storage and instant geysers: lukewarm water usually means a scaled element or a tired thermostat, and a tripping MCB means a leak to earth, which we test for on every visit.

Book Havells geyser repair →

Racold and Bajaj geysers are repaired and serviced too, and so are Crompton and V-Guard ones.

On every visit

We check the earthing on every visit

  • The earth is tested, whether we came for a descale or a leak
  • The safety valve is checked, and normal drips told apart from a real leak
  • Switch-off confirmed with a thermometer after any thermostat or cut-out work

If your geyser trips the MCB, keep it switched off at the MCB until a technician has tested it for a leak to earth.

Before you book

Two checks to try first

Neither needs any tools.

Press the reset button on the back

  1. Switch the geyser off at the wall.
  2. Press the red reset button, the thermal cut-out, on the back of the geyser.
  3. Switch it back on. If hot water comes back, it costs nothing.

If it trips again, something else has failed first. Book a visit and we find that too.

Check whether it is the geyser or the tap

  1. Run the hot tap in a second bathroom.
  2. If that one runs hot, the geyser is working.
  3. The fault is the mixer in the first bathroom, a much cheaper job.

A mixer diluting the hot water looks exactly like a geyser that has stopped heating.

Still not working?Book a technician

Reviews

Geyser repair reviews from Bengaluru homes

All →
4.7from 2,650+ bookings in Bengaluru
Pradeep Kalyan Nagar · Geyser★ 5.0
Geyser was giving only lukewarm water. Technician checked it and found the heating element problem. Replaced and tested it. Now working fine.
Shilpa M. JP Nagar · Geyser★ 5.0
Booked geyser servicing because it was making noise. Technician explained that there was lot of scale and did descaling. Good service.
Irfan HBR Layout · Geyser★ 5.0
Geyser stopped heating suddenly. Person came same day and checked properly. Problem was with the element and got it replaced.
Lakshmi Malleshwaram · Geyser★ 5.0
Installation was done nicely. Technician checked the fittings, water connection and earthing also. He tested the geyser before leaving.
Rohan P. Electronic City · Geyser★ 5.0
Good and simple service. Called for geyser issue, technician came as promised and told me the price before doing the repair. No surprise charges.

Messages customers sent us after a geyser repair.

Symptoms

No hot water? Find the symptom

Tap the geyser problem you have to see what usually causes it and what the repair costs. An element, thermostat or tank part is priced before it goes in.

No hot water at all, power light on

UsuallyElement burnt out, faster on borewell water; thermostat or cut-out tripped; burnt terminal

FixTest the element; fit a matched element and new gasket, or reset and test the thermostat

Cost₹1,299 to ₹4,199

Only lukewarm, and slower than before

UsuallyScale caked on the element; sediment in the tank; thermostat drifted; a mixer diluting it

FixDescale and flush; replace the element if it is scaled beyond saving

Cost₹649 to ₹3,399

Drips from the pipe underneath

UsuallyNormal expansion (a few drops); worn safety valve; high line pressure on a booster pump

FixNothing if it is normal; replace the valve; fit a pressure-reducing valve if pressure is the cause

Cost₹0 to ₹2,799

Trips the MCB or RCCB

UsuallyCurrent leaking through a cracked element sheath; damp terminal block; shared circuit

FixInsulation test; replace the element; verify the earth before re-energising

Cost₹499 to ₹3,199

Leaking from the body, stain on the ceiling

UsuallyFlange gasket perished; corroded nipple or union; inner tank perforated

FixGasket, nipple or union repaired; a perforated tank is replaced, never sealed

Cost₹699 to ₹1,599

Gas geyser clicks, will not light

UsuallyFlat batteries; low water flow on a top floor; choked inlet filter; empty cylinder; electrode or solenoid

FixBatteries, gas, flow, filter, electrode, diaphragm, then solenoid, in that order

Cost₹299 to ₹2,399

All 14 geyser faults and their costs
Rumbling or popping while heating

UsuallyScale and sediment on the tank floor flashing to steam; loose element or bracket

FixDrain, flush and descale; re-secure the bracket. Overdue, though safe for now

Cost₹649 to ₹2,999

Scalding hot, never switches off

UsuallyThermostat contacts welded; capillary out of its pocket; only the cut-out is stopping it

FixSwitch off at the MCB. Replace thermostat and cut-out; confirm cut-off with a thermometer

Cost₹1,099 to ₹3,599

Tingle or shock from the tap or body

UsuallyElement insulation broken down; no earth, or a poor one, at the geyser point

FixSwitch off at the MCB and call. Replace the element; earthing faults reported to you

Cost₹1,299 to ₹3,199

Gas geyser lights, then cuts off

UsuallyDirty flame sensor; sooted heat exchanger; low flow; a sealed room starving it of air

FixSensor, burner and flue service; ventilation checked and reported

Cost₹699 to ₹1,799

Hot water smells of eggs, or runs brown at first

UsuallyBacteria reacting with the anode rod, the sacrificial rod that corrodes so the tank does not; borewell sediment; a corroding tank

FixFlush and sanitise; replace the anode rod; straight answer if the tank is going

Cost₹649 to ₹1,899

Hot water at a trickle, cold is fine

UsuallyOutlet choked with scale flakes; inlet strainer blocked; aerator; half-closed isolation valve

FixFlush, clear the outlet and strainer, purge air; replace the valve if its screen is gone

Cost₹399 to ₹1,699

Error code, or a dead display

UsuallyTemperature sensor; dry-heating trip on a part-empty tank; surge or damp on the board

FixFill and power-cycle first; sensor; board only after the sensor is cleared

Cost₹0 to ₹3,599

Instant geyser goes cold after a minute

UsuallyOften nothing: a 1L or 3L unit is a basin heater; partly failed element; flow too high for its rating

FixMeasure flow and temperature rise; if it meets its rating, we say so and charge no repair

Cost₹0 to ₹2,599

Some ranges start at ₹0 because the fix is a check you can do at home. A technician’s visit is billed at no less than the visit charge, from ₹299. It is the minimum charge, and a costlier repair has it built into the price.

Quick check · your water

How hard is the water where you live?

480 to 560 ppmSoftModerateHard

Descale every six months

Whitefield is in the hardest band in our water table. Ask for a coated element when yours is replaced.

  • Service and descaleFrom ₹639
  • Element, 15 to 25 L storageFrom ₹1,299
Book a geyser descale
380 to 440 ppmSoftModerateHard

Descale every six months

Borewell and tanker water at this band furs an element inside a year if nobody descales it.

  • Service and descaleFrom ₹639
  • Element, 15 to 25 L storageFrom ₹1,299
Book a geyser descale
290 to 380 ppmSoftModerateHard

Descale every 12 to 18 months

Scale builds slowly on moderate water, but an element that is never descaled still furs up in time.

  • Service and descaleFrom ₹639
  • Element, 15 to 25 L storageFrom ₹1,299
Book a geyser descale

Parts

Geyser parts we replace

These are fitted prices, with labour counted in. You are told which part it is before it goes into your geyser.

Fitted prices for 14 parts
Common geyser parts, fitted
PartFitted priceNotes
Heating element, 2 kW, 15 to 25L storage₹1,299 to ₹3,199Price depends on brand and flange pattern; capacity makes little difference. Coated is worth it on borewell water
Heating element, 35 to 50L storage₹2,599 to ₹4,199Villas, bathtubs, PG blocks
Heating element, 3 kW instant₹1,399 to ₹2,399Runs hotter than a storage element, so scale kills it faster
Capillary thermostat₹1,099 to ₹1,999Replaced with the element when the element overheated
Thermal cut-out, manual reset₹999 to ₹1,599If it tripped, something else failed first; we find that too
Temperature sensor, digital models₹1,099 to ₹1,799The most common digital-geyser fault
Control or display board, digital models₹2,399 to ₹3,599Past six or seven years old, often where replacement wins
Magnesium anode rod, with flush₹1,099 to ₹1,899Decides whether the tank lasts four years or ten. Every 2 to 3 years on hard water
Safety valve (MFSV)₹899 to ₹1,699Never plugged or swapped for a plain non-return valve
Pressure-reducing valve, with safety valve₹1,599 to ₹2,799High-rise booster pumps; a new valve alone would weep again in months
Flange gasket, nipple or union₹699 to ₹1,599The gasket is replaced every time the flange is opened
Gas electrode, diaphragm, micro-switch or solenoid₹899 to ₹1,799Tested in order; only what fails is replaced
Gas ignition board₹1,199 to ₹2,399We do not fit unbranded ignition boards on a gas appliance
Gas flame or overheat sensor₹899 to ₹1,599Often only needs cleaning; we test before we sell
What the code on your display meansHavells, Racold, gas boards
What the code on your display means
CodeBrandMeaningUsual fix
E3Havells digital storageTemperature sensor open circuit; usually a wet or corroded connector, and the geyser itself is fineCheck the harness, test the sensor, replace it. The board only after that
E4Havells digital storageTemperature sensor short circuit; same family as E3Same path: harness, then sensor
E5Havells digital storageDry-heating protection: the tank was part-empty when it switched onFill until a hot tap runs steadily, power-cycle for five minutes. Often free
E1Racold Omnis, Eterno, IntelloThermistor fault; on leak-detecting models, a deliberate shutdownTest the sensor. On a leak model, isolate and look for water; do not keep resetting
E1 / E2 / E3Gas geyser ignition boardsUsually ignition failed / flame lost / overheat trip, but not standard across brandsE1: batteries, gas, flow, electrode. E2: flame sensor. E3: exchanger, flue and ventilation
MCB / RCCB trips, no codeAll brandsCurrent leaking to earth, normally through a failed element sheathInsulation test; replace the element; verify the earth before re-energising
Your water is probably why it failedhardness by area, solar, gas, apartments
Your water is probably why it failed
AreaReported hardnessWhat it means
Whitefield, Varthur480 to 560 ppmSix-monthly descale; coated element; anode rod every 2 to 3 years
Sarjapur Road460 to 540 ppmSix-monthly descale; expect early element failure if skipped
Electronic City410 to 470 ppmSix-monthly descale; PG blocks wear elements several times faster
Marathahalli, KR Puram, Hoodi380 to 440 ppmSix-monthly descale; inlet strainer silts with grit
Yelahanka, Devanahalli, north Bengaluru360 to 430 ppmSix-monthly descale; anode inspected yearly
Bellandur, HSR, Hebbal, BTM Layout, JP Nagar, Bannerghatta Road290 to 380 ppmBetween the two; go by what the element looks like at the first descale
Jayanagar, Indiranagar, Koramangala, Malleshwaram, Rajajinagar, Banashankari160 to 240 ppmCauvery supply; every two years is enough

Answers

Geyser repair questions

How soon can a technician reach me?

Within 60 minutes, wherever you live in Bengaluru, between 8 AM and 9 PM.

Do you repair Racold, AO Smith and Havells geysers?

Yes. We repair, service and install Racold, AO Smith and Havells geysers, and Bajaj, Crompton and V-Guard ones too, on storage, instant and gas models that are out of warranty.

Do you install geysers?

Yes. We install new geysers and replace old ones. The technician fixes the geyser to the wall, connects the inlet and outlet, fits the safety valve and checks the earthing before switching it on.

My geyser keeps tripping the MCB. Is it safe to use?

No. Switch it off at the MCB and do not use it until it has been checked. A furred element that overheats is the usual cause.

Is this just a way of selling me a new geyser?

No. A repair is priced first. We only suggest a replacement when the tank itself has failed, or when the repair would cost nearly as much as a new geyser.

My geyser is above a false ceiling, or my gas geyser is in the bathroom. Can you still work on it?

Yes. We check the access on the call. For a gas geyser, the room’s ventilation is checked and reported.

Do I pay the visit charge on top of the geyser repair?

No. A visit costs from ₹299 and includes the diagnosis. If you go ahead, we subtract the visit charge from the repair bill. If you do not, you pay for the visit alone.

What if my geyser cannot be repaired?

You pay only the visit fee, from ₹299. A perforated inner tank is not repairable: welding, epoxy and sealant all fail, and anyone offering to seal one is selling you a leak into your ceiling. If a control board on an eight-year-old unit costs more than the geyser is worth, or a spare has been discontinued, we give you the numbers to compare and leave the decision with you. Replacement units typically run ₹6,499 to 21,999 plus ₹499 to 899 to fit.

Will you fit an original geyser part or a local one?

We fit OEM-compatible parts by default, named on the quote and on the invoice and shown to you before fitting. Where a manufacturer part is available for your model we say so and quote it separately. Where a genuine part is discontinued, common on Racold, Bajaj and Venus units older than about eight years, we say so and offer a good-quality equivalent, marked as one, with its own warranty. In the borewell belt a ₹399 uncoated element often does not survive a year, so the coated one at around ₹1,799 is the cheaper choice over three years. Old parts are left with you.

My geyser is above a false ceiling, or my gas geyser is inside the bathroom. Can you still work on it?

Yes to the ceiling unit; they are common in Bengaluru apartments. It usually has to be dropped through the trap door, so we tell you the extra time before starting, and we check the tray and drain while it is down. Yes to the gas geyser too, with the ventilation checked and reported. If the room has no permanent opening we will recommend moving the unit to a balcony or utility area, and we will not sign off an installation we think is unsafe.

Talk to a person

No hot water this morning? Book a geyser repair today.

A person calls you back within 10 minutes, late at night included. You pay after the repair, never in advance, and no OTP is asked for.

Or send a photo on WhatsApp

Reviewed on

Book a repair

A person calls you back within 10 minutes.

1Which appliance? Tap one
2What is wrong? Tap one
3Where do we call you?
  • Visit from ₹299, taken off your repair bill if you go ahead
  • Pay after the repair
  • No advance, no OTP

Your details are used to arrange your repair. Privacy

Not sure what it is? Send a photo on WhatsApp