Steel and black OTG oven with three control knobs

OTG and built-in oven repair in Bengaluru, at your door.

Repairs start at ₹349. The visit is charged from ₹299. Once you agree to the repair, the visit charge is taken off the repair bill. We repair OTGs and built-in wall ovens.

  • 4.7 from 2,650+ bookings
  • Up to 180-day warranty
  • Same day
Step 1 of 2What’s wrong with it? Tap one

Next, add your name and number. A person calls back in 10 minutes.

Step 2 of 2

Pick the job

OTG and built-in oven repair

The technician repairs your oven where it stands, on the counter or in the wall.

All charges →
Technician testing the wiring behind the knobs of an OTG oven

Oven repair

From ₹699

visit charge included

A built-in oven is repaired in its cabinet unless the job needs access from the back.

  • Diagnosed in your kitchen and priced before any work
  • A major repair runs from ₹1,799, part included
Book an oven repair
Technician fitting a heating element in an OTG, the old one on a cloth

Element replaced

From ₹699

OTG; built-in from ₹1,799

A dead element is the commonest oven fault. Each element and the thermostat is tested before any part is fitted.

  • Generic OTG rods stocked in Bengaluru, usually fitted the same visit
  • Only the failed element replaced, bake or grill
Book an element repair
Gloved hands fitting a thermostat behind the control knobs of an OTG

Thermostat repair

From ₹799

generic capillary thermostat

If the oven is slow to heat or burns the edges, the cavity is measured with a thermometer before any part is changed.

  • The cavity measured at 180 and 220 C
  • The thermostat or sensor recalibrated or replaced
Book a thermostat repair
Timer switch taken out of a steel OTG oven and held in gloved hands

Timer and switch

Visit from ₹299

generic parts, usually the same visit

If the timer will not run or the selector skips, a worn knob is ruled out first.

  • A worn knob ruled out before any part
  • Generic timers and switches, normally fitted the same visit
Book a timer repair
Gloved hands pressing a new door seal into place around a built-in wall oven

Door repair

From ₹599

door gasket; a hinge pair from ₹1,499

A gap at the top lets the heat out. Hinges usually stretch from leaning on the open door.

  • Hinges replaced as a pair, so the door closes square
  • A hardened or torn seal replaced
Book a door repair
Built-in oven pulled out of its cabinet with its control board being tested

Control board

From ₹349

reset or connector clean; UI module from ₹3,499

A dead touch panel is often the child lock or a wet key. The cheap causes are checked before any module.

  • Lock cleared and connectors cleaned first
  • The main board only after proving it dead
Book a control board repair

By type

OTG, convection OTG and built-in oven repair

Tell us whether your oven sits on the counter or is built into the wall. We repair both kinds at home, on every brand out of warranty.

OTG oven repair

An OTG has top and bottom elements, a thermostat knob and a timer. If only one element glows or the timer stops ticking, the element, the selector or the timer is the usual cause.

  • Heating element
  • Thermostat
  • Timer
  • Selector switch
Book now →

Convection OTG repair

A fan at the back moves the hot air for even baking, and many add a rotisserie. Uneven baking with the elements glowing points to the fan motor.

  • Fan motor
  • Rotisserie motor
  • Elements
  • Thermostat
Book now →

Built-in oven repair

A built-in is a wall oven with a fan, electronic controls and a door that runs hot. The technician takes it out of the cabinet to reach the wiring.

  • Fan element
  • Temperature sensor
  • Door seal
  • Control board
  • Cooling fan
Book now →

IFB and Bosch oven repair, and every other make

Any OTG or built-in oven can be repaired, in or out of warranty and whatever its age. Brands not listed here are repaired too.

IFB oven service and repair

IFB makes convection microwaves and built-in ovens. On a built-in oven the fan element, the temperature sensor and the door seal are the usual faults.

Book IFB oven repair →

Bosch oven service and repair

Bosch built-in ovens bake with a fan and a ring element under electronic control. Uneven baking usually means the fan or the element; an error on the display, the sensor or the board.

Book Bosch oven repair →

Siemens and Whirlpool built-in ovens are repaired too, along with Elica and Faber ovens and Morphy Richards and Bajaj OTGs.

Before you book

Two checks to try first

An unset clock is often mistaken for a dead oven.

Check the timer and the child lock

  1. If the clock is flashing, set it.
  2. If a lock or key symbol shows, switch the child lock off.
  3. Pick a mode again and see whether it heats.

A built-in oven with the clock unset or the lock on will not run the elements at all. It looks like a dead oven.

Watch which element glows

  1. Switch to each mode for a minute.
  2. Note which element lights up.
  3. Tell us which one stays dark when we call back.

That one test tells the technician which spare to put in the van.

Still not working?Book a technician

Reviews

Oven repair reviews from Bengaluru homes

All →
4.7from 2,650+ bookings in Bengaluru
Priya Nair Malleshwaram · OTG★ 5.0
My OTG was not heating from few days. Technician came and checked the heating element. He explained the issue and replaced it. Oven is working fine now.
Faizal R. Yelahanka · Built-in oven★ 5.0
Good service. My built in oven was taking too much time to get hot. They checked properly and told thermostat issue. Got it fixed in same visit.
Swati Jayanagar · Oven★ 5.0
Called for oven repair. Person came, checked first and gave price before starting. I liked that. Work was done neatly.
Rohit Sarjapur Road · OTG★ 5.0
OTG suddenly stopped heating but light was coming. Technician checked and found small problem, luckily no major part replacement. Reasonable service.
Deepa K. Banashankari · Oven★ 4.0
Very decent experience. Technician was polite and explained everything in simple language. He also tested the oven after repair before leaving.

Messages customers sent us after an oven repair.

Symptoms

Oven not heating? Find the symptom

Look up what your oven is doing for the common cause, the fix and the price. Any element, thermostat or board is named and priced before fitting.

Not heating at all, light and fan work

UsuallyBurnt-out element, the commonest oven fault; failed capillary thermostat; tripped thermal cut-out; cooked spade terminal; heating relay on the board (built-in)

FixContinuity-test each element and the thermostat, replace the failed part, re-terminate with a high-temperature crimp

Cost₹699 to ₹1,999 OTG
₹1,799 to ₹4,499 built-in

Top burns, bottom stays raw

UsuallyLower element open-circuit; convection fan not turning; burnt selector contact; thermostat drifted high; door seal leaking at the top

FixReplace the dead element or free the fan; verified with a thermometer on the centre rack

Cost₹799 to ₹3,499 OTG
₹1,999 to ₹5,499 built-in

Slow to heat, never reaches the set temperature

UsuallyThermostat or sensor out of calibration; low mains voltage; tired element; hardened door seal; grease insulating the cavity; boxed-in cabinet

FixCavity measured at 180 and 220 C; thermostat or sensor recalibrated or replaced; seal replaced; clearance corrected

Cost₹599 to ₹2,199 seal, calibration
₹1,499 to ₹3,499 thermostat, sensor

Smokes and smells burnt every time

UsuallyBaked-on grease on the floor and lower element, most of these calls; forgotten foil; grease in the fan housing; saturated catalytic liners; a new oven curing, which is normal

FixStrip-out deep clean; liners replaced only if saturated. A burning plastic smell is a different fault: the hot plug, below

Cost₹0 if you clean it
₹1,499 to ₹2,499 deep clean

Door will not shut, gap at the top

UsuallyStretched hinge springs or a snapped hinge claw, usually from leaning on the open door; hardened or torn gasket; glass pack shifted after a clean; worn latch on pyrolytic ovens

FixHinges replaced as a pair, gasket replaced, door re-seated and squared, latch adjusted

Cost₹599 to ₹2,199 gasket
₹1,499 to ₹4,499 hinge pair

Grinding or rattling from inside

UsuallyDry convection fan bearing; blade striking a loose rear baffle; greasy cooling blower; loose rack rail or base tray

FixRacks out and fan-only first, it is often loose shelving; then tighten the baffle, or replace the fan motor or blower

Cost₹599 to ₹1,199 tighten, clean
₹1,599 to ₹4,499 fan motor

All 14 oven faults and their costs
Trips the MCB or RCCB the moment it starts

UsuallyElement leaking to earth after months unused or the monsoon; cracked element sheath; water in the lamp holder; chafed harness; shorted fan motor

FixInsulation test of each element and motor to earth; the leaking part replaced. A merely damp element sometimes dries out at 100 C with the door ajar. Never tape or bypass the RCCB

Cost₹1,199 to ₹4,499 element, lamp holder
₹2,499 to ₹5,999 harness, motor

Display or touch panel dead

UsuallyChild lock or demo mode; stuck or wet key; touch membrane failed after steam and grease got behind the fascia; loose ribbon; main board, or the two boards no longer talking

FixLock cleared and MCB off for 60 seconds first; connectors cleaned and reseated; UI module swapped; the main board only after proving it dead

Cost₹349 to ₹1,499 reset, connector clean
₹3,499 to ₹11,999 UI module

Inside light not working

UsuallyBlown 25 W E14 lamp rated to 300 C; corroded or cracked ceramic holder; cracked glass cover letting steam onto the contacts

FixChange the lamp yourself with the MCB off and the oven cold: cover off anticlockwise, same rating in. A household LED fails within days. Holder replaced if the new lamp stays dark

Cost₹349 to ₹899 lamp
₹899 to ₹1,999 lamp and holder

Knob turns but nothing happens, timer stopped ticking (OTG)

UsuallyWorn clockwork timer, the classic 3 to 5 year OTG failure; pitted selector switch; stripped thermostat shaft; rounded-out knob; cord damaged at the strain relief

FixPull the knob and turn the bare spindle with pliers: if the oven responds you need only a new knob, and the visit charge, from ₹299, is the whole bill. Otherwise the timer, switch or thermostat is replaced, all cheap generic parts

Cost₹499 to ₹1,799

Switches itself off mid-bake, restarts after a wait

UsuallyThermal cut-out tripping because the cabinet has no clearance; front vent blocked by a plinth or shelf; clogged or failed cooling blower; grease insulating the cavity; Samsung S-01 auto-off after a very long run, which is by design

Fix20 to 30 mm side and rear clearance restored and the vent cleared; blower cleaned or replaced; cut-out and any heat-damaged terminal replaced. A flush-boxed cabinet is a carpentry job first

Cost₹799 to ₹1,999 clearance, cut-out
₹1,999 to ₹5,499 cooling blower

Burning plastic smell, plug or socket hot

UsuallyA 2.5 to 3.5 kW oven on a 6 A socket or an extension board; arcing socket contacts; damaged cord; scorched terminal block inside the oven

FixSwitch off at the MCB and stop using it. Oven-side cord and terminal block replaced; the socket and circuit corrected by a licensed electrician to a dedicated 16 A point with earth

Cost₹599 to ₹2,499 oven side
Electrical point quoted separately

Door glass cracked or shattered

UsuallyThermal shock from a wet cloth or a cold tray; a chipped edge propagating; weight on the open door; cleaner sprayed on hot glass; rare inclusions in toughened glass

FixIsolate at the MCB and keep children away until it is cleared. Photograph the rating plate: the model number is the difference between a 3-day and a 3-week wait

Cost₹1,799 to ₹4,499 OTG glass
₹2,499 to ₹7,499 built-in pane

Steam oven says descale, or steam has stopped

UsuallyScale in the steam generator from borewell water; blocked nozzle; fouled tank seal or level sensor; air-locked pump; descale programme started and never completed

FixRun the oven's own descale programme with the maker's descaler first, never vinegar or shop acid. Boiler and nozzle stripped and descaled if that fails; pump or sensor replaced only if proven

Cost₹799 to ₹1,799 descale
₹2,499 to ₹5,999 pump, sensor, boiler

A range from ₹0 means you might fix it yourself for nothing. With a technician’s visit, the lowest bill is the visit charge, from ₹299. It is the minimum charge. A repair that costs more already counts the visit charge in its price.

Quick check

Is it an OTG or a built-in oven?

Usually one element, fitted the same visit

Generic OTG elements are stocked in Bengaluru. If two elements on one OTG have failed, a new OTG is usually the better buy, and you hear that before any work.

  • OTG heating elementFrom ₹699
  • Capillary thermostatFrom ₹799
  • Door gasketFrom ₹599
Book OTG repair

Repaired in its cabinet where it can be

A built-in needs the kitchen clear for an hour. Generic parts fit most Faber, Elica, Kaff, Hafele and Glen cavities; Bosch and Siemens usually need OEM.

  • Lower / bake element, genericFrom ₹1,799
  • NTC temperature sensorFrom ₹899
  • Door hinge pair, genericFrom ₹1,499
Book built-in oven repair

Parts

Oven parts we replace

Fitted prices, so the part and the labour together. Each part is named before it goes into your oven.

Fitted prices for 18 parts
Common oven parts, fitted
PartFitted priceNotes
OTG heating element, bake or grill₹699 to ₹1,799Generic rods stocked in Bengaluru, usually fitted the same visit. Two dead elements on one OTG usually means replace the OTG
Built-in lower / bake element₹1,799 to ₹4,499 generic
₹3,999 to ₹8,999 OEM
Generic matches most Faber, Elica, Kaff, Hafele and Glen cavities; Bosch and Siemens usually need OEM
Built-in upper / grill element₹1,599 to ₹3,999 generic
₹3,499 to ₹7,999 OEM
Often twin-circuit; if only the centre section glows the element is replaced as a unit
Capillary thermostat, 50 to 300 C₹799 to ₹2,199 generic
₹2,499 to ₹4,999 branded
Second most replaced OTG part after the element. The capillary must not be kinked when fitted
NTC temperature sensor (built-in)₹899 to ₹2,499The part behind most sensor codes, and far cheaper than the board people are often sold instead
Convection fan motor₹1,599 to ₹4,499 generic
₹3,999 to ₹8,999 OEM
Housing degreased at the same time, or the new motor goes the same way
Tangential cooling blower₹1,999 to ₹5,499Behind the top fascia. Clogs with kitchen grease, then the oven cuts out mid-bake
Door hinge pair₹1,499 to ₹4,499 generic
₹3,999 to ₹8,999 OEM
Always in pairs; one new spring against one tired one twists the door. Pyrolytic hinges cost more
Door gasket / cavity seal₹599 to ₹2,199The cheapest fix for “never reaches temperature” and the most under-diagnosed
Oven lamp, 25 W E14, 300 C₹349 to ₹899 lamp
₹899 to ₹1,999 with holder
We will tell you on the phone how to change it yourself
Timer, 0 to 60 minutes (OTG)₹699 to ₹1,599Generic 60-minute units stocked locally; normally a same-visit fix
Selector / function switch₹699 to ₹1,799Symptom is “only some functions work”
One-shot thermal cut-out₹399 to ₹1,199Never replaced without finding why it tripped, or the new one blows too
Rotisserie motor (OTG)₹599 to ₹1,499Often the skewer is overloaded or mis-seated and the motor is fine
Power cord, 16 A plug, terminal block₹499 to ₹1,399Replaced whenever the pins or block show heat discolouration. Socket and circuit work is the electrician's
Touch / user-interface module₹3,499 to ₹11,999Usually the real failure behind a dead panel on Bosch, Siemens and Samsung built-ins; cheaper than the main board
Main control PCB (built-in)₹4,499 to ₹13,999The part most often sold unnecessarily. Sensor, element and relay proven first; board-level repair where the model is discontinued
Inner door glass / full door assembly₹2,499 to ₹7,499 pane
₹5,999 to ₹17,999 full door
Strictly model-specific, national spares order. On an older OTG the glass often costs more than the OTG
What the code on your display meansBosch, Siemens, Samsung, Whirlpool, LG
What the code on your display means
CodeBrandMeaningUsual fix
E011 / F2E0 / C-d0 / C-F2Bosch, Siemens · Whirlpool · SamsungA key stuck, held or wet. Some sources read E011 as a door-lock fault, so keys first, lock secondMCB off for 60 seconds, dry-clean the fascia, press each key once. If it returns, the touch module
E005 / E101 / E106 / F3E0 / C-20 / C-22 / F1Bosch, Siemens · Whirlpool · Samsung · LGTemperature sensor open, shorted or out of rangeReseat the sensor plug, then replace the NTC probe. Not the board
E015 / E220 / F5E0 / F5E1 / C-d1Bosch, Siemens · Whirlpool · SamsungDoor lock or latch fault, often after a pyrolytic cycle, sometimes with the door stuck shutDo not force the door; it bends the hinge. Latch assembly or lock motor replaced
E305 / C-F0 / C-F1Bosch, Siemens · SamsungThe two boards have stopped talking, or the board's memory has failedMCB off for 60 seconds, ribbon connector reseated; then the failed board
C-21SamsungCavity hotter than the settingStop using it and call: a welded relay or a failed sensor can run the cavity far past setpoint
F9 / F19LGOven failed to reach temperature in timeUsually an open element (electric) or igniter (gas), then the sensor
S-01 / dC / dESamsungSafety auto-off after a very long run; divider check on Dual Cook modelsNot a fault. Restart, or fit or remove the divider to match the mode
E1 / E2Digital OTGs, air-fryer ovens, some Faber, Elica, Kaff, Hafele, Glen built-insE1 sensor open or unplugged; E2 sensor shorted or over-temperaturePower off five minutes, check the sensor plug, replace the sensor if out of spec
No code at allMechanical OTGs: Bajaj, Morphy Richards, Philips, Prestige, Havells, Borosil, UshaA knob-operated OTG has no sensor and no display, so it has no error codesDiagnosed by measurement. Anyone quoting a code for one is guessing
Voltage, cabinets and the monsoon
Voltage, cabinets and the monsoon
What is localWhich ovensWhat to do
Raw borewell draws above 500 ppm in Whitefield and Sarjapur, above the mixed-supply area averages; Cauvery areas 160 to 240 ppmSteam and combi-steam ovens onlyDescale twice a year on borewell supply, once on Cauvery; fill the tank with RO or filtered water
Low or swinging voltage at the socket, often worst in the eveningEvery oven heats slowly at 180 V, an element gives about 60% of its rated heat. Surges damage the boards and touch panels on built-insCheck the socket voltage in the evening before booking an “element gone” job. A stabiliser is worth it for an electronic built-in, pointless for a mechanical OTG
Oven boxed in flush and run off a 6 A point, the commonest modular-kitchen defectBuilt-in ovens, 2.5 to 3.5 kW20 to 30 mm clearance at the sides and back, front vent clear, a dedicated 16 A point with earth. Otherwise it cooks its own electronics and cuts out mid-bake
The June to September monsoon, then an oven used only for the November baking seasonAny oven left unused for months: the element packing absorbs moisture and leaks to earth on first switch-onBake-only at 100 C for 30 minutes with the door ajar before the first bake of the season. If the RCCB still trips, call

Answers

OTG & oven repair questions

Can someone come out today?

Yes, we come anywhere in Bengaluru. A built-in oven needs the kitchen clear for an hour.

Do you repair electric ovens and OTGs?

Yes. We repair countertop OTGs and built-in electric wall ovens out of warranty, from IFB, Bosch, Siemens and Whirlpool to Elica, Faber, Morphy Richards and Bajaj.

Why is my OTG not heating properly?

It is usually one failed element, or the thermostat. Switch to each mode for a minute, watch which element glows, and tell us when we call back.

Is it worth repairing, or should I just buy a new one?

If two elements on one OTG have failed, a new OTG is usually the better buy, and the technician tells you so before any work. For any other fault you see the repair price first, and if you say no, you pay only for the visit, from ₹299.

Are the parts you fit original, or local?

Generic elements fit most built-in cavities, including Faber, Elica, Kaff, Hafele and Glen. Bosch and Siemens usually need OEM. Where both fit, both are quoted.

Is the visit fee extra to the oven repair?

No. The visit costs from ₹299, diagnosis included. Once you approve the repair, the visit charge is counted in the repair bill and not added to it. Say no, and you pay only the visit charge.

What if you open it up and it cannot be fixed?

Then you pay only the visit fee, from ₹299, and the technician tells you why: usually a discontinued board, a cracked cavity, or a repair bill above the price of a replacement. We put the two numbers side by side and say which one we would choose.

How long does a spare part take?

Generic elements, thermostats, timers, switches, lamps and seals are stocked in the Bengaluru market and usually fitted the same visit or the next day. OEM-coded boards, touch modules, door glass and hinges come from the national spares channel and realistically take 3 to 10 working days. We give you that date at the quote. If a part turns out to be discontinued, we tell you within 48 hours; nothing is charged for a part that never arrives.

Talk to a person

Oven not heating? Get it fixed today.

Send your number and a person calls back within 10 minutes, at any hour. You pay once the oven works, with no advance and no OTP.

Or send a photo on WhatsApp

Reviewed on

Book a repair

A person calls you back within 10 minutes.

1Which appliance? Tap one
2What is wrong? Tap one
3Where do we call you?
  • Visit from ₹299, taken off your repair bill if you go ahead
  • Pay after the repair
  • No advance, no OTP

Your details are used to arrange your repair. Privacy

Not sure what it is? Send a photo on WhatsApp