Reference
What your appliance's error code means
An error code names the check your appliance failed. It does not say why. Some codes clear in 2 minutes. Others mean a part has to be fitted, from about ₹899 for a washing machine door interlock to ₹5,499 for an AC leak repair with a full gas charge.
By Kaif Sharieff, Fixit BLR · published · reviewed
What a code tells you, and what it leaves out
A washing machine runs a few checks as it works: that water comes in, that it drains away, that the drum turns, that the heater warms the water and that the door locks. When one of those checks fails, the machine stops and shows a code. ACs, purifiers and microwaves do the same with their own checks.
The code tells you which check failed, and nothing about the cause. A drain code looks the same whether a coin is stuck in the filter or the drain pump has burnt out. The first is a free clean that takes 10 minutes. The second is a new drain pump at ₹1,199 to ₹3,199 fitted. Anyone who quotes a price from the code alone, over the phone, is guessing.
Common codes and what they usually mean
The letters change from brand to brand, and sometimes between two models of the same brand. If your code is not here, check the manual, or send us a photo of the display.
| Code | Seen on | What the machine checked | What it usually is |
|---|---|---|---|
| OE / 5E / E2 / P11 | Washing machine | Water did not drain in time | The drain filter first, the pump second |
| IE / 4E / E1 | Washing machine | Water did not come in in time | A tap half closed, or a silted inlet gauze |
| UE / dC / E3 | Washing machine | The load is off balance | Not a fault. Spread the load out and level the machine |
| dE / E4 | Washing machine | The door did not lock | Laundry caught in the door, then the interlock |
| HE / E5 | Washing machine | Water never reached temperature | Scale on the element, in a borewell area |
| LE / E9 | Washing machine | Water is sitting in the base tray | A real leak. Stop the machine now |
| Repeating beeps / solid red light | Water purifier: Kent, Aquaguard | The UV lamp is not lighting | The lamp or its choke. Do not drink from it until it is fixed |
| U0 / CH38 / E554 | AC: Daikin, LG, Samsung | The gas pressure is low | A leak, which has to be found and repaired before any gas goes in |
| U4 / CH05 / E101 | AC: Daikin, LG, Samsung | The indoor and outdoor units stopped talking | A surge or a loose connecting wire, and only then the board |
A door code on a washing machine is often a sleeve or a sock caught in the seal. If it is the interlock itself, that part is ₹899 to ₹2,199 fitted. Each appliance page has its full fault list with prices: washing machine repair, AC repair and water purifier repair.
How to clear a drain code on a front loader
This is the code most worth trying yourself, and it takes about 10 minutes.
- Switch the machine off at the wall socket. If the last wash was hot, wait for the water to cool first.
- Lay a towel and a shallow tray under the small flap at the bottom front. Expect 1 to 2 litres of water.
- Open the flap. Some machines have a thin drain hose beside the filter: pull it out, take off its cap and let the water run into the tray.
- Turn the filter anticlockwise, slowly, and pull it out. Take out any coin, hairclip, button or lint, and rinse the filter under a tap.
- Screw it back in firmly, close the flap, switch on and run a rinse and spin.
If the code comes back on the next cycle, the filter was not the cause. Look for a kink in the drain hose behind the machine. If the hose is clear and the pump hums without moving water, the pump has failed and needs a technician.
How to clear a fill code
- Check that the tap behind the machine is fully open.
- Look along the inlet hose for a kink where the machine was pushed back against the wall.
- Turn the tap off, unscrew the hose at the tap end, and rinse the small mesh filter inside it. Above 400 ppm this gauze silts up in 6 to 12 months, which covers most of the outer east of Bengaluru.
- Refit the hose hand-tight, open the tap, and check for drips before you start a cycle.
Codes after a power cut
An appliance can show a code that means nothing after a power cut or a voltage dip. Switch off at the socket, wait 60 seconds and switch on again. If the same code returns within one or two cycles, the machine has run its check again and failed it again. That is a real fault, and resetting it again will not fix it.
Codes that mean stop now
- A leak or base-tray code, LE or E9 on many washing machines, means a float switch has found water in the base. Switch off at the socket and close the tap.
- A door code on a microwave is a safety switch doing its job. Do not try to get round it. The capacitor inside can hold a dangerous charge for days after the microwave is unplugged, so this is not a home repair.
- A geyser that has tripped its over-temperature cut-out has tripped for a reason. Leave it switched off at the MCB.
In all three cases, leave the appliance off and book a visit. Do not reset it to see what happens.
What to send when you book
Send a photo of the display showing the code, the brand, and the model number from the rating plate. The model number guide shows where the plate is on each appliance. With those three things we can usually name the likely part and its price band before anyone comes out. The final price is quoted after the diagnosis and before any repair starts. The visit costs from ₹299, and if you go ahead with the repair, the visit fee comes off the repair bill.
Questions
Can you quote a price from the code over the phone?
No, and nobody else can either. A drain code on a washing machine can be a filter clean that takes 10 minutes and costs nothing, or a drain pump at ₹1,199 to ₹3,199 fitted, and the display looks the same in both cases. The visit, from ₹299, pays for the diagnosis. You get the fitted price before any repair starts, and if you go ahead with the repair, we take the visit fee off your repair bill.
Will resetting the machine clear the code for good?
Sometimes. After a power cut or a voltage dip a code can mean nothing: switch off at the socket, wait 60 seconds and restart. If the same code comes back within one or two cycles, the machine has failed its own check twice, so the fault is real. Never reset a leak or base-tray code and run the machine again.
Does the same code mean the same repair on every brand?
No. The letters change by brand and the price changes by appliance. One drain fault shows as OE on one machine, 5E on another and E2 on a third, and the pump behind it is ₹1,199 to ₹3,199 fitted. On an AC the same low-gas fault reads U0 on a Daikin, CH38 on an LG and E554 on a Samsung. The model number is what turns a code into a named part.
Which codes mean I should stop using the appliance?
Three of them: a leak or base-tray code on a washing machine (LE or E9 on many models), a door code on a microwave, and a geyser that has tripped its over-temperature cut-out. Switch each one off at the socket or the MCB, do not reset it, and book a visit.
Pages that go with this
We repair all major appliance brands
We repair every make out of warranty, across Bengaluru. Tap yours to book.
Still not working? Book now, pay after the job.
Tell us what it is doing and we will tell you what it usually is, and what it usually costs, before anyone comes out.
Photo ✓✓

